CP PLUS 8-Port PoE Switch with 2 Gigabit Uplink Ports

The CP PLUS 8 port PoE switch is designed to connect compatible network devices in IP CCTV surveillance and Ethernet networking installations. Model CP-DNW-HPU8G2-96-V3 features eight 10/100 Mbps Power over Ethernet (PoE) ports and two Gigabit uplink ports, making it suitable for network layouts that need several powered devices and separate uplink connections.

A PoE switch can simplify compatible installations by carrying data and electrical power over a single Ethernet cable to supported devices. This can be useful when connecting IP cameras in homes, shops, offices and other premises.

Key Features of CP PLUS 8-Port PoE Switch

1. Eight PoE Network Ports

The switch includes eight RJ45 PoE ports operating at 10/100 Mbps. These ports can connect compatible PoE-powered devices such as supported IP cameras and other network equipment.

Before connecting devices, check their PoE standards, power consumption and network requirements. The number of devices that can be powered simultaneously depends on the total power budget and the consumption of each connected device.

2. Two Gigabit Uplink Ports

The CP-DNW-HPU8G2-96-V3 includes two 1000 Mbps Gigabit RJ45 uplink ports. These can be used to connect compatible network equipment, such as an NVR, router or another switch.

The uplink ports operate separately from the eight 10/100 Mbps PoE ports. Actual network throughput depends on the connected equipment, traffic and overall network configuration.

3. 96W Total PoE Power Budget

This model has a total PoE power budget of 96W, with a maximum output of 30W per PoE port as listed by the manufacturer.

The 96W figure represents the total available PoE power budget, not 96W for every port. When planning an installation, add together the power requirements of the connected devices and leave sufficient capacity within the switch’s limits.

4. IEEE 802.3af/at PoE Standards

The switch supports IEEE 802.3af and IEEE 802.3at PoE standards. These standards help determine compatibility between the switch and powered devices.

Always check the exact power standard required by each IP camera or other connected device. A device’s power requirement must remain within the supported output limits.

5. Extended Transmission Mode

The manufacturer lists an extended transmission mode that can support distances up to 250 metres at 10 Mbps using Cat5e or better cabling under supported conditions.

In standard mode, the listed transmission distance is 0–100 metres at 100 Mbps for the PoE ports. Extended mode reduces the transmission rate and should only be used where the longer distance is appropriate for the installation.

Actual results depend on the cable, connected devices and installation conditions.

6. Unmanaged, Plug-and-Play Design

This is an unmanaged switch designed for straightforward installation without the usual configuration required by a managed switch. The manufacturer describes it as a plug-and-play device.

Users should still follow the installation guide, use compatible Ethernet cables and ensure the connected equipment is configured correctly.

7. Network Protection and AI Watchdog

The official specifications list ESD protection, surge protection and AI Watchdog support. These functions are designed to help with network equipment protection and monitoring.

Protection ratings and watchdog behaviour depend on the manufacturer’s implementation and installation conditions. They should not be treated as a guarantee against every electrical fault or network issue.

Technical Specifications

• Brand: CP PLUS
• Model: CP-DNW-HPU8G2-96-V3
• Product type: Unmanaged PoE network switch
• Total network ports: 10
• PoE ports: 8 × RJ45, 10/100 Mbps
• Uplink ports: 2 × RJ45 Gigabit, 1000 Mbps
• Total PoE power budget: 96W
• Maximum output per PoE port: 30W
• PoE standards: IEEE 802.3af and IEEE 802.3at
• Network standards: IEEE 802.3, 802.3u, 802.3ab and 802.3x
• Switching capacity: 5.6 Gbps
• Packet forwarding rate: 4.166 Mpps
• MAC address table: 8K
• Packet buffer: 3 Mb
• Forwarding method: Store-and-forward
• Extended transmission mode: Up to 250m at 10 Mbps under supported conditions
• Standard transmission distance: Up to 100m at the specified standard-mode rate
• AI Watchdog: Supported
• Power source: Built-in power supply
• Power consumption: Less than 5W as listed for the switch itself; PoE load is additional
• Operating temperature: -10°C to +50°C
• Operating humidity: 10%–95%, non-condensing
• Dimensions: 320 × 207 × 44 mm
• Weight: Approximately 1.78 kg

Specifications are based on the manufacturer’s available product information. Check the latest datasheet for the exact version supplied.

Benefits of Using a CP PLUS PoE Switch

Simplifies Compatible IP Camera Wiring

With compatible PoE cameras, a single Ethernet cable can carry both network data and power. This can reduce separate power-cabling requirements at each camera location.

Connects Multiple Network Devices

Eight PoE ports allow several compatible devices to connect to the network, while the two Gigabit uplink ports provide connections to other network equipment.

Helps Plan CCTV Installations

The switch can be used as part of a suitable IP CCTV setup with compatible cameras, network cables and an NVR or other network equipment.

Provides a Defined Power Budget

The 96W total PoE budget helps installers plan the combined power requirements of connected devices before installation.

Offers an Extended-Mode Option

Where supported by the network layout and cabling, extended mode can help with selected longer cable runs. Remember that the listed rate falls to 10 Mbps in this mode.

Where Can You Use This PoE Switch?

Depending on the network design and device compatibility, this switch may be suitable for:

• IP CCTV camera installations
• Shops and showrooms
• Office surveillance networks
• Small business networking
• Compatible Ethernet devices requiring PoE
• Network layouts that need Gigabit uplink connections

Choose the switch based on the number of devices, PoE power budget, required network speed and cable distances.

Frequently Asked Questions

1. How many PoE ports does this CP PLUS switch have?

It has eight 10/100 Mbps PoE ports and two Gigabit uplink ports.

2. What is the total PoE power budget?

The total PoE power budget is 96W. Each PoE port has a listed maximum output of 30W, subject to the overall budget.

3. Can I connect IP CCTV cameras to this switch?

Yes, compatible PoE IP cameras can be connected. Check their PoE standards, power requirements and network compatibility before installation.

4. What are the Gigabit uplink ports used for?

They connect the switch to compatible network equipment such as an NVR, router or another switch. Each uplink port supports 1000 Mbps.

5. Does this switch support long-distance transmission?

The manufacturer lists an extended mode of up to 250 metres at 10 Mbps under supported conditions using Cat5e or better cabling. Standard mode has a shorter listed transmission distance.

6. Is this a managed switch?

No. This model is an unmanaged switch designed for straightforward plug-and-play installation.

7. Can every PoE port deliver 30W at the same time?

The listed maximum per port is 30W, but the total available power is limited to 96W. The combined power draw of connected devices must stay within that budget.

8. Is this switch suitable for a home or office CCTV system?

It may suit a compatible IP CCTV installation in a home, shop or office. Confirm the camera count, network speed, power budget and cable distances before choosing the model.

Buy CP PLUS Networking Products from Navdurga Computer

Planning an IP CCTV installation for your home, shop or office? Navdurga Computer can help you explore CP PLUS cameras, PoE switches, NVRs and networking accessories based on your installation requirements.

Contact Navdurga Computer to confirm compatibility and select the appropriate equipment for your network.

More Info : Click Now

Official Website : https://cpplusworld.com/